34. Segment data structure

34.1. Introduction

.intro: This is the design of the segment data structure.

34.2. Overview

.over.segments: Segments are the basic units of tracing and shielding. The MPM also uses them as units of scanning and colour, although pool classes may subdivide segments and be able to maintain colour on a finer grain (down to the object level, for example).

.over.objects: The mutator’s objects are stored in segments. Segments are contiguous blocks of memory managed by some pool.

.segments.pool: The arrangement of objects within a segment is determined by the class of the pool which owns the segment. The pool is associated with the segment indirectly via the first tract of the segment.

.over.memory: The relationship between segments and areas of memory is maintained by the segment module. Pools acquire tracts from the arena, and release them back to the arena when they don’t need them any longer. The segment module can associate contiguous tracts owned by the same pool with a segment. The segment module provides the methods SegBase, SegLimit, and SegSize which map a segment onto the addresses of the memory block it represents.

.over.hierarchy: The Segment datastructure is designed to be subclassable (see design.mps.protocol). The basic segment class (Seg) supports colour and protection for use by the tracer, as well as support for a pool ring, and all generic segment functions. Clients may use Seg directly, but will most probably want to use a subclass with additional properties.

.over.hierarchy.gcseg: The segment module provides GCSeg - a subclass of Seg which has full support for GC including buffering and the ability to be linked onto the grey ring.

34.3. Data Structure

struct SegStruct *Seg
struct GCSegStruct *GCSeg

The implementations are as follows:

typedef struct SegStruct {      /* segment structure */
  Sig sig;                      /* <code/misc.h#sig> */
  SegClass class;               /* segment class structure */
  Tract firstTract;             /* first tract of segment */
  RingStruct poolRing;          /* link in list of segs in pool */
  Addr limit;                   /* limit of segment */
  unsigned depth : ShieldDepthWIDTH; /* see <code/shield.c#def.depth> */
  AccessSet pm : AccessLIMIT;   /* protection mode, <code/shield.c> */
  AccessSet sm : AccessLIMIT;   /* shield mode, <code/shield.c> */
  TraceSet grey : TraceLIMIT;   /* traces for which seg is grey */
  TraceSet white : TraceLIMIT;  /* traces for which seg is white */
  TraceSet nailed : TraceLIMIT; /* traces for which seg has nailed objects */
  RankSet rankSet : RankLIMIT;  /* ranks of references in this seg */
} SegStruct;

typedef struct GCSegStruct {    /* GC segment structure */
  SegStruct segStruct;          /* superclass fields must come first */
  RingStruct greyRing;          /* link in list of grey segs */
  RefSet summary;               /* summary of references out of seg */
  Buffer buffer;                /* non-NULL if seg is buffered */
  Sig sig;                      /* design.mps.sig */
} GCSegStruct;

.field.rankSet: The rankSet field represents the set of ranks of the references in the segment. It is initialized to empty by SegInit().

.field.rankSet.single: The Tracer only permits one rank per segment [ref?] so this field is either empty or a singleton.

.field.rankSet.empty: An empty rankSet indicates that there are no references. If there are no references in the segment then it cannot contain black or grey references.

.field.rankSet.start: If references are stored in the segment then it must be updated, along with the summary (.field.summary.start).

.field.depth: The depth field is used by the Shield (impl.c.shield) to manage protection of the segment. It is initialized to zero by SegInit().

.field.sm: The sm field is used by the Shield (impl.c.shield) to manage protection of the segment. It is initialized to AccessSetEMPTY by SegInit().

.field.pm: The pm field is used by the Shield (impl.c.shield) to manage protection of the segment. It is initialized to AccessSetEMPTY by SegInit(). The field is used by both the shield and the ANSI fake protection (impl.c.protan).

.field.black: The black field is the set of traces for which there may be black objects (that is, objects containing references, but no references to white objects) in the segment. More precisely, if there is a black object for a trace in the segment then that trace will appear in the black field. It is initialized to TraceSetEMPTY by SegInit().

.field.grey: The grey field is the set of traces for which there may be grey objects (i.e containing references to white objects) in the segment. More precisely, if there is a reference to a white object for a trace in the segment then that trace will appear in the grey field. It is initialized to TraceSetEMPTY by SegInit().

.field.white: The white field is the set of traces for which there may be white objects in the segment. More precisely, if there is a white object for a trace in the segment then that trace will appear in the white field. It is initialized to TraceSetEMPTY by SegInit().

.field.summary: The summary field is an approximation to the set of all references in the segment. If there is a reference R in the segment, then RefSetIsMember(summary, R) is TRUE. The summary is initialized to RefSetEMPTY by SegInit().

.field.summary.start: If references are stored in the segment then it must be updated, along with rankSet (.field.rankSet.start).

.field.buffer: The buffer field is either NULL, or points to the descriptor structure of the buffer which is currently allocating in the segment. The field is initialized to NULL by SegInit().

.field.buffer.owner: This buffer must belong to the same pool as the segment, because only that pool has the right to attach it.

34.4. Interface

34.4.1. Splitting and merging

.split-and-merge: There is support for splitting and merging segments, to give pools the flexibility to rearrange their tracts among segments as they see fit.

Res SegSplit(Seg *segLoReturn, Seg *segHiReturn, Seg seg, Addr at)

.split: If successful, segment seg is split at address at, yielding two segments which are returned in segLoReturn and segHiReturn for the low and high segments respectively. The base of the low segment is the old base of seg. The limit of the low segment is at. The base of the high segment is at. This limit of the high segment is the old limit of seg. seg is effectively destroyed during this operation (actually, it might be reused as one of the returned segments). Segment subclasses may make use of the optional arguments; the built-in classes do not.

.split.invariants: The client must ensure some invariants are met before calling SegSplit():

  • .split.inv.align: at must be a multiple of the arena grain size, and lie between the base and limit of seg. Justification: the split segments cannot be represented if this is not so.

  • .split.inv.buffer: If seg is attached to a buffer, the buffered region must not include address at. Justification: the segment module is not in a position to know how (or whether) a pool might wish to split a buffer. This permits the buffer to remain attached to just one of the returned segments.

.split.state: Except as noted above, the segments returned have the same properties as seg. That is, their colour, summary, rankset, nailedness etc. are set to the values of seg.

Res SegMerge(Seg *mergedSegReturn, Seg segLo, Seg segHi)

.merge: If successful, segments segLo and segHi are merged together, yielding a segment which is returned in mergedSegReturn. segLo and segHi are effectively destroyed during this operation (actually, one of them might be reused as the merged segment). Segment subclasses may make use of the optional arguments; the built-in classes do not.

.merge.invariants: The client must ensure some invariants are met before calling SegMerge():

  • .merge.inv.abut: The limit of segLo must be the same as the base of segHi. Justification: the merged segment cannot be represented if this is not so.

  • .merge.inv.buffer: One or other of segLo and segHi may attached to a buffer, but not both. Justification: the segment module does not support attachment of a single seg to 2 buffers.

  • .merge.inv.similar: segLo and segHi must be sufficiently similar. Two segments are sufficiently similar if they have identical values for each of the following fields: class, grey, white, nailed, rankSet. Justification: There has yet to be a need to implement default behaviour for these cases. Pool classes should arrange for these values to be the same before calling SegMerge().

.merge.state: The merged segment will share the same state as segLo and segHi for those fields which are identical (see .merge.inv.similar). The summary will be the union of the summaries of segLo and segHi.

34.5. Extensibility

34.5.1. Splitting and merging

Res (*SegSplitMethod)(Seg seg, Seg segHi, Addr base, Addr mid, Addr limit)

.method.split: Segment subclasses may extend the support for segment splitting by defining their own “split” method. On entry, seg is a segment with region [base,limit), segHi is uninitialized, mid is the address at which the segment is to be split. The method is responsible for destructively modifying seg and initializing segHi so that on exit seg is a segment with region [base,mid) and segHi is a segment with region [mid,limit). Usually a method would only directly modify the fields defined for the segment subclass.

.method.split.next: A split method should always call the next method, either before or after any class-specific code (see design.mps.protocol.overview.next-method).

Res (*SegMergeMethod)(Seg seg, Seg segHi, Addr base, Addr mid, Addr limit)

.method.merge: Segment subclasses may extend the support for segment merging by defining their own merge method. On entry, seg is a segment with region [base,mid), segHi is a segment with region [mid,limit), The method is responsible for destructively modifying seg and finishing segHi so that on exit seg is a segment with region [base,limit) and segHi is garbage. Usually a method would only modify the fields defined for the segment subclass.

.method.merge.next: A merge method should always call the next method, either before or after any class-specific code (see design.mps.protocol.overview.next-method).

.split-merge.shield: Split and merge methods may assume that the segments they are manipulating are not in the shield queue.

.split-merge.shield.flush: The shield queue is flushed before any split or merge methods are invoked.

.split-merge.shield.re-flush: If a split or merge method performs an operation on a segment which might cause the segment to be queued, the method must flush the shield queue before returning or calling another split or merge method.

.split-merge.fail: Split and merge methods might fail, in which case segments seg and segHi must be equivalently valid and configured at exit as they were according to the entry conditions. It’s simplest if the failure can be detected before calling the next method (for example, by allocating any objects early in the method).

.split-merge.fail.anti: If it’s not possible to detect failure before calling the next method, the appropriate anti-method must be used (see design.mps.protocol.guide.fail.after-next). Split methods are anti-methods for merge methods, and vice-versa.

.split-merge.fail.anti.constrain: In general, care should be taken when writing split and merge methods to ensure that they really are anti-methods for each other. The anti-method must not fail if the initial method succeeded. The anti-method should reverse any side effects of the initial method, except where it’s known to be safe to avoid this (see .split-merge.fail.summary for an example of a safe case).

.split-merge.fail.anti.no: If this isn’t possible (it might not be) then the methods won’t support after-next failure. This fact should be documented, if the methods are intended to support further specialization. Note that using va_arg with the args parameter is sufficient to make it impossible to reverse all side effects.

.split-merge.fail.summary: The segment summary might not be restored exactly after a failed merge operation. Each segment would be left with a summary which is the union of the original summaries (see .merge.state). This increases the conservatism in the summaries, but is otherwise safe.

.split-merge.unsupported: Segment classes need not support segment merging at all. The function SegClassMixInNoSplitMerge() is supplied to set the split and merge methods to unsupporting methods that will report an error in checking varieties.